|
|
| Line 28: |
Line 28: |
|
| |
|
| These parameters can be used to indvidually colorize the zone overlay pattern. By default, red is the active zone and green is the ??? zone. | | These parameters can be used to indvidually colorize the zone overlay pattern. By default, red is the active zone and green is the ??? zone. |
|
| |
| ==Alarm Check Method==
| |
| *Alarmed Pixels -
| |
|
| |
| Choosing this Check Method will grey out many of the available parameters. This can simplify the tuning process, and could possibly be a better starting point for learning to adjust the many advanced parameters that are enabled with the other options.
| |
|
| |
| *Filtered Pixels -
| |
|
| |
| Choosing this Check Method opens up the Filtered parameters for adjustment in addition to the Alarmed Pixels above. This should give more accuracy, once you know how to adjust the various parameters and assist with eliminating false alarms and triggering on desired conditions.
| |
|
| |
| *Blob Pixels -
| |
|
| |
| Choosing this Check Methos opens up all of the available parameters. Enabling Blobs provides one more analysis for determination of what is a valid alarm and what is not.
| |
|
| |
| ==Minimum Pixel Threshold==
| |
| These setting are used to define limits for the difference in value between a pixel and its predecessor in the reference image.
| |
|
| |
| I believe that this value (and the Maximum value as well) defines the amount of change that a single pixel must undergo, from the prior image (the reference image) and the current image, in order for the pixel to have been considered to have changed.
| |
|
| |
| Small abberations in lighting or auto exposure camera adjustments may cause the explicit value of a pixel to vary by small amounts from image to image. This parameter allows you to set the limits of what will be considered a "changed pixel". For example, if your camera points to a blank white wall, and you raise a black colored item into view, then the change in any one pixel will be great, indeed, extreme. If however, you raise a white piece of paper, then the change that an individual pixes sees will be more subtle. Setting this minimum value too high, may allow a white cat to walk undetected across the view of the white wall.
| |
|
| |
| The default value for this parameter is X%. Generally, this value may range in the 5% to 15% range.
| |
|
| |
| ==Maximum Pixel Threshold==
| |
| See the Minimum Pixel Threshold (above) for some explanation.
| |
|
| |
| The default value for this parameter is 0% or 0 (zero) pixels, which disables the check. In other words, a pixel that changes from extreme white to extreme black will always be considered to be changed. This value is probably best left at a value of 0 (zero).
| |
|
| |
| ==Minimum Alarmed Area==
| |
|
| |
| ==Maximum Alarmed Area==
| |
|
| |
| ==Filter Width and Filter Height (pixels)==
| |
| This parameter is always specified in Pixels, even when Percentages are the selected units.
| |
|
| |
| This parameter defines a group of pixels and should always be an odd number.
| |
|
| |
| 3 x 3 is the default value, and 5 x 5 is also suggested as another valid option. It is suggested that these numbers be small in number.
| |
|
| |
| ==Minimum Filtered Area==
| |
|
| |
| * This value should always be equal to or less than the Minimum Alarmed Area
| |
|
| |
| ==Maximum Filtered Area==
| |
|
| |
| * This value should always be equal to or less than the Maximum Alarmed Area
| |
|
| |
| ==Minimum Blob Area==
| |
| * The following Blob parameters are only available if you have selected "Blobs" as the "Alarm Check Method" above.
| |
|
| |
| When two or more Filtered areas touch or share a boundary, they probably should be evaluated as one contiguous area and not as separate entities. A Blob is the coalesced or consolodated area of multiple filtered areas.
| |
|
| |
| The Minimum blob area the smallest area that would be considered to be a blob.
| |
|
| |
| ==Maximum Blob Area==
| |
| This parameter is probably best left at the default value of 0 (zero) or disabled.
| |
|
| |
| ==Minimum Blobs==
| |
| Normally, you would want any single blob to trigger an event, so the default value of 1 (one) should suffice. In some circumstances, it may benefit to have only one blob NOT trigger an event, in which case, setting this value to 2 or higher may serve some special purpose.
| |
|
| |
| ==Maximum Blobs==
| |
| I believe that the usefulness of this parameter is negligible. Normally set to 0 (zero), it is probably best left at that value.
| |
