Vivotek

D-Link DCS-2103

Checked in versions of ZoneMinder 1.25.

I have successfully setup a D-Link DCS-2103 (fw 1.0) on an Ubuntu 11.10 Server i386 using RTSP at 1280x800, 24-bit color and streaming at 16FPS using RTSP. To make this work, use the following settings:

Sorce Type: Ffmpeg
Source Path: rtsp://username:password@хх.хх.хх.хх/live1.sdp
Remote Image Colours: 24 bit colour
Capture Width (pixels): 1280
Capture Height (pixels): 800

IP7131

ZM < v. 1.24

In versions of ZoneMinder prior to 1.24, the only way to use the Vivotek 7131 camera was by streaming the snapshot (which gives you an inconsistent FPS of 1 - 3). Use /cgi-bin/video.jpg as the Remote Host Path (Under Source).

ZM >= v. 1.24

Starting with version 1.24 of ZoneMinder, RTSP is supported. As the Vivotek 7131 camera supports RTSP, we can now make full use of this camera. I have successfully setup a a Vivotek 7131 on an Ubuntu 8.10 Server using RTSP at 640x480, 24-bit color and streaming at 20FPS using RTSP. To make this work, use the following settings:

Remote Protocol: RTSP
Remote Method: RTP/RTSP
Remote Host Name: x.x.x.x
Remote Host Port: 554
Remote Host Path: /live.sdp
Remote Host SubPath: /trackID=
Remote Image Colours: 24 bit colour
Capture Width (pixels): 640
Capture Height (pixels): 480

IP7138

< v. 1.24

In versions of ZoneMinder prior to 1.24, the only way to use the Vivotek 7138 camera was by streaming the snapshot (which gives you an inconsistent FPS of 1 - 3). Use /cgi-bin/viewer/video.jpg as the Remote Host Path (Under Source).

IP7135

http://www.zoneminder.com/forums/viewtopic.php

IP8330/32

See this How-To for accessing the 4 streams of either MJPEG, MPEG4 or H.264
http://www.zoneminder.com/wiki/index.php/How_to_setup_MPEG-4_streaming_with_RTSP_monitor_from_a_Vivotek_IP8332_camera

A summary for MJPEG:
Remote Protocol: HTTP
Remote Method: Simple
Remote Host Name: Put in the cameras IP or hostname
Remote Host Path: /video.mjpg

And for MPEG or H.264:
Remote Protocol: RTSP
Remote Method: RTP/RTSP
Remote Host Name: Put in the cameras IP or hostname
Remote Host Path: /live.sdp

PZ7132

ZM v1.24.2

RTSP
Source Type: Ffmpeg
Source Path : rtsp://user:pass@x.x.x.x/live.sdp

Works pretty good, decent image via ffmpeg and RTSP, but not a consistent 30fps, more like in the mid 20's with a wired connection. Only got about 5fps via WiFi, and that was with it less then about 8 feet from the 802.11g access point through one wall so using it via WiFi is a wash. But that's why I wanted one that was also wired as a fallback and it's PoE so that's a plus. So it needs at least one wire either way. (Laptop has no problem through that same wall and is even farther away.)

Wrote a web based interface to control the PTZ it's available here: http://www.curtronics.com/ftp/vtek-ptz/vtek-ptz.html /

FD8134

ZM v1.24.2

Remote Protocol: RTSP
Remote Method: RTP/RTSP
Remote Host Name: Put in the cameras IP or hostname
Remote Host Path: /live.sdp

The camera's web interface has a network section can set the URL. The basic authentication can be set here too.

The video section can set the network settings. MPEG worked. H.264 and JPEG didn't seem to work.

Running more that two camera on the network required to set the maximum frame rate in ZM to 30.

I (jtwang) have this working with H.264 and JPEG. It appears to be a general ZoneMinder limitation that the Remote source only works with MPEG. Make sure you set up the stream type in the camera's config, somewhat confusingly you have to set up the type of stream (JPEG / MPEG / H.264) in the Audio/Video config, then enable RTSP in the Network config. For H.264 use the ffmpeg source, see this page - but use the proper URL for the Vivotek camera (i.e. /live.sdp)

PZ8111

The camera will work with zoneminder 1.25 with some minor modifications to the template PanasonicIp.pm script. The changed commands are listed below. The the only tricky part was zoom. For some reason the zoom ui is callinging Tele and Wide functions instead of zoomConTele andzoomConWide

+++

sub sendCmd {

   my $self = shift;
   my $cmd = shift;

   my $result = undef;

   printMsg( $cmd, "Tx" );

   my $req = HTTP::Request->new( GET=>"http://".$self->{Monitor}->{ControlAddress}."/cgi-bin/camctrl/$cmd" );
   my $res = $self->{ua}->request($req);

   if ( $res->is_success )
   {
       $result = !undef;
   }
   else
   {
       Error( "Error check failed: '".$res->status_line()."'" );
   }

   return( $result );

}

sub moveConUp {

   my $self = shift;
   Debug( "Move Up" );
   my $cmd = "camctrl.cgi?move=up";
   $self->sendCmd( $cmd );

}

sub moveConDown {

   my $self = shift;
   Debug( "Move Down" );
   my $cmd = "camctrl.cgi?move=down";
   $self->sendCmd( $cmd );

}

sub moveConLeft {

   my $self = shift;
   Debug( "Move Left" );
   my $cmd = "camctrl.cgi?move=left";
   $self->sendCmd( $cmd );

}

sub moveConRight {

   my $self = shift;
   Debug( "Move Right" );
   my $cmd = "camctrl.cgi?move=right";
   $self->sendCmd( $cmd );

}

sub Tele {

   my $self = shift;
   #my $params = shift;
   #my $step = $self->getParam( $params, 'step' );
   Debug( "Zoom Tele" );
   my $cmd = "camctrl.cgi?zoom=tele";
   $self->sendCmd( $cmd );

}

sub Wide {

   my $self = shift;
   #my $params = shift;
   #my $step = $self->getParam( $params, 'step' );
   Debug( "Zoom Wide" );
   my $cmd = "camctrl.cgi?zoom=wide";
   $self->sendCmd( $cmd );

}

+++

MD7560

ZM v1.24.2

You can setup one of the 4 available streams to fit your needs. In order to do so, open the "Configuration" section using the webinterface and switch to "Advanced Configuration". Click on "Audio and video" and change the quality settings by clicking on one of the "Video quality settings for stream" links. Click on JPEG to get MJPEG or MPEG4 to use RTSP later on.

As I'm not sure which mode is the best, please pick one:

MJPEG with FFmpeg:
Source type: Ffmpeg
Source Path: http://<camera-ip>/video.mjpg (or whatever name you've configured)

MJPEG with Remote Source:
Source type: Remote
Remote Protocol: HTTP
Remote Method: Simple
Remote Host Name: Put in the cameras IP or hostname
Remote Host Path: /video.mjpg

To change or view the video stream names, check the "Network" section in the webinterface in advanced mode.