Difference between revisions of "How to Setup a FLIR F-Series Thermal Camera with MPEG4 streaming"
From ZoneMinder Wiki
Jump to navigationJump to search
(FLIR HOWTO) |
m |
||
Line 4: | Line 4: | ||
==Prerequisites== | ==Prerequisites== | ||
*IP address of camera. | * IP address of camera. | ||
*Username and password for the camera. | * Username and password for the camera. | ||
*Administrator access to Zone Minder. | * Administrator access to Zone Minder. | ||
==Checking camera configuration== | ==Checking camera configuration== | ||
#Access the camera web interface | # Access the camera web interface | ||
#Open the Video IR configuration and configure using the following settings: | # Open the Video IR configuration and configure using the following settings: | ||
**Enabled: Yes | ** Enabled: Yes | ||
**Associated uFLIRish Id: 0 | ** Associated uFLIRish Id: 0 | ||
**Channel Id: 0 | ** Channel Id: 0 | ||
**Video Source: Type: IR | ID: 0 | ** Video Source: Type: IR | ID: 0 | ||
**Format: PAL | ** Format: PAL | ||
**Interface: .... | ** Interface: .... | ||
**Port: 554 | ** Port: 554 | ||
**RTP/RTSP over HTTP Port: 8080 | ** RTP/RTSP over HTTP Port: 8080 | ||
**Stream Name: ch0 | ** Stream Name: ch0 | ||
**Use External IP: no | ** Use External IP: no | ||
**Enable Multicast: no | ** Enable Multicast: no | ||
**Codec Type: MPEG4 | ** Codec Type: MPEG4 | ||
**Bit Rate: 3000000 | ** Bit Rate: 3000000 | ||
**Rate Control: CBR | ** Rate Control: CBR | ||
**I-Frame Interval: 30 | ** I-Frame Interval: 30 | ||
**Image Size: D1 | ** Image Size: D1 | ||
**Frame Rate: 10 | ** Frame Rate: 10 | ||
**Interlaced: no | ** Interlaced: no | ||
<br/> | <br/> | ||
==Zone Minder configuration== | ==Zone Minder configuration== | ||
#[[How_to_login|Login]] to Zone Minder. | # [[How_to_login|Login]] to Zone Minder. | ||
#Click on the "Add New Monitor" link located at the bottom of the page, this will take you to the configuration page for adding a new camera. | # Click on the "Add New Monitor" link located at the bottom of the page, this will take you to the configuration page for adding a new camera. | ||
#General Tab - Use the following settings: | # General Tab - Use the following settings: | ||
**Name of the monitor | ** Name of the monitor | ||
**Source Type - Remote | ** Source Type - Remote | ||
**Function - Modetect | ** Function - Modetect | ||
#Source Tab - Use the following settings: | # Source Tab - Use the following settings: | ||
**Remote Protocol - RTSP | ** Remote Protocol - RTSP | ||
**Remote Method - RTP/Unicast | ** Remote Method - RTP/Unicast | ||
**Remote Host Name - <ip-address> | ** Remote Host Name - <ip-address> | ||
**Remote Host Port - 554 | ** Remote Host Port - 554 | ||
**Remote Host Path - /ch0 | ** Remote Host Path - /ch0 | ||
**Remote Image Colours - 24 bit colour | ** Remote Image Colours - 24 bit colour | ||
**Capture Width (pixels) - 720 | ** Capture Width (pixels) - 720 | ||
**Capture Height (pixels) - 576 | ** Capture Height (pixels) - 576 | ||
**Preserve aspect ratio - OFF | ** Preserve aspect ratio - OFF | ||
**Orientation - Normal | ** Orientation - Normal | ||
==Monitor Resolution== | ==Monitor Resolution== | ||
The resolution can be changed, some of the available resolutions: | The resolution can be changed, some of the available resolutions: | ||
**QCIF 176x144 | ** QCIF 176x144 | ||
**4CIF 704x576 | ** 4CIF 704x576 | ||
**D1 720x576 | ** D1 720x576 |
Revision as of 13:14, 7 November 2011
Go back to the How To pages...
Prerequisites
- IP address of camera.
- Username and password for the camera.
- Administrator access to Zone Minder.
Checking camera configuration
- Access the camera web interface
- Open the Video IR configuration and configure using the following settings:
- Enabled: Yes
- Associated uFLIRish Id: 0
- Channel Id: 0
- Video Source: Type: IR | ID: 0
- Format: PAL
- Interface: ....
- Port: 554
- RTP/RTSP over HTTP Port: 8080
- Stream Name: ch0
- Use External IP: no
- Enable Multicast: no
- Codec Type: MPEG4
- Bit Rate: 3000000
- Rate Control: CBR
- I-Frame Interval: 30
- Image Size: D1
- Frame Rate: 10
- Interlaced: no
Zone Minder configuration
- Login to Zone Minder.
- Click on the "Add New Monitor" link located at the bottom of the page, this will take you to the configuration page for adding a new camera.
- General Tab - Use the following settings:
- Name of the monitor
- Source Type - Remote
- Function - Modetect
- Source Tab - Use the following settings:
- Remote Protocol - RTSP
- Remote Method - RTP/Unicast
- Remote Host Name - <ip-address>
- Remote Host Port - 554
- Remote Host Path - /ch0
- Remote Image Colours - 24 bit colour
- Capture Width (pixels) - 720
- Capture Height (pixels) - 576
- Preserve aspect ratio - OFF
- Orientation - Normal
Monitor Resolution
The resolution can be changed, some of the available resolutions:
- QCIF 176x144
- 4CIF 704x576
- D1 720x576