Trendnet

TV-IP100

Trendnet TV-IP100 works ok. http://x.x.x.x/video.cgi

TV-IP100W-N

great little wireless camera with digital zoom

Remote Protocol: HTTP
Remote Method: Simple
Remote Host Name: user:pass@x.x.x.x (admin:admin is the default user/pass)
Remote Host Port: 80
Remote Host Path: /MJPEG.CGI

TV-IP110 & TV-IP110W

Remote Protocol: HTTP
Remote Method: Simple
Remote Host Name: <username>:<password>@x.x.x.x
Remote host Port: 80
Remote Host Path: /cgi/mjpg/mjpg.cgi
Remote Image Colors: 24 bit color
Capture Width: 640
Capture Height: 480

The capture height and width can be changed using the camera's web interface by modifying the "Video Quality" setting.

VGA = 640 x 480
QVGA = 320 x 240
QQVGA = 160 x 120

TV-IP201P

The TV-IP201P works ok. Use the following settings:

Remote Protocol: HTTP
Remote Method: Simple
Remote Host Name: user:pass@x.x.x.x (admin:admin is the default user/pass and 192.168.0.30 is the default IP)
Remote Host Port: 80
Remote Host Path: /goform/capture

TV-IP252P

Remote Protocol: HTTP
Remote Method: Simple
Remote Host Name: user:pass@x.x.x.x (admin:admin is the default)
Remote Host Port: 80
Remote Host Path: cgi/mjpg/mjpg.cgi

TV-IP300

Just remember to turn 1.0 in ZM_HTTP_VERSION in the Options > Network tab. In the x.x.x.x/cgi-bin/video.jpg gives 352 x 240 jpg.

TV-IP301

This camera sends the wrong mime/type and is not compatible with ZoneMinder natively but can be made to work.

http://www.zoneminder.com/forums/viewtopic.php?t=7320

TV-IP400 / TV-IP400W

These are cheap but fun Pan Tilt Zoom IP cameras and are now also supported by ZoneMinder.

New Driver and instructions for ZM 1.23.x : http://www.sfpeter.com/2008/07/31/new-trendnet-tv-ip400w-controller-for-zoneminder-123x/

Older Driver and instructions for 1.22.x: http://www.sfpeter.com/2007/08/14/controlling-the-trendnet-tv-ip400w-camera-with-zoneminder/ The above link is missing the "Move" tab when creating the control. You need to select "Can Move", "Can Move Diagonally" and "Can Move Relative".

TV-IP501P

This camera works just like the IP400 without the PTZ contols.

Remote Protocol: HTTP
Remote Method: Simple
Remote Host Name: user:pass@x.x.x.x (admin:admin is the default user/pass)
Remote Host Port: 80
Remote Host Path: /MJPEG.CGI

TV-IP501W

the Trendnet IP501W works. Here are the settings

Source Type: Remote

Remote Protocol: HTTP

Remote Method: Simple

Remote Host Name: username:password@IP-address

Remote Host Port: 80

Remote Path: /video.cgi

TV-IP512P

HTTP
Source Type: Remote
Remote Host Name: user:pass@<IP Address of Camera>
Remote Host Port: 80 (Default)
Remote Host Path: /video/mjpg.cgi (for mjpeg stream)
Remote Host Path: /image/jpeg.cgi (for a single jpeg frame)

RTSP
Source Type: ffmpeg
Source Path: rtsp://user:pass@<IP Address of Camera>/play1.sdp (or play2.sdp)

ZoneMinder 1.24.2 (Haven't tried earlier versions)

RTSP works with ffmpeg as above pulling 30fps when camera set to 30fps for that Profile.

Alternatively, the monitor can be configured:

Source Type: Remote
Remote Protocol: RTSP
Remote Method: RTP/Unicast
Remote Host Name: user:pass@<IP Address of Camera>
Remote Host Port: 554
Remote Host Path: /play1.sdp

When using the above ffmpeg RTSP and camera is set to Night Mode using the 30fps setting fps drop to 15fps in the dark as per the warning that this may happen at low light levels.

TV-IP512WN

The TV-IP512WN is pretty much the same device as TV-IP512P. It features an additional WLAN interface and can be used with the same settings as the TV-IP512P.

TV-IP522P

Warning: even though this is a 'MegaPixel' camera, it has a very wide-angle lens so the image detail isn't very high. Furthermore, replacement 1/2" lenses seem to be hard to find.

ZM configuration is similar to TV-IP512P (above) except the 522 has multiple video profiles, which should be specified as

Remote Host Path: /video/mjpg.cgi?profileid=1

(1, 2, or 3, depending on the desired profile)

Also be sure to set Capture Width and Capture Height appropriately.

MPEG and RTSP were not tested but the camera does support them.[1]