AVtech

AVTech

Other cameras may be similar to those below

Notes: This camera works well and can be forced into permanent IR mode which helps with focusing.; It has a real IR filter than physically moves into place when IR mode engages.; It uses a M12 thread CCTV board lens which can be changed.; the camera streams stop if it does not see a clear image or movement for a period of time i.e. if you defocus it can point it at a plain piece of paper the stream in ZoneMinder will stop. Connecting to the camera via VLC will restart the ZoneMinder stream. You should add an hourly cron job to telnet to the camera on port 554 to keep it alive.

On the camera: You need to enable anonymous login. This in in the config > online page; not under users where you might think.; You need to change the FPS to the number zoneminder can support on your hardware i.e. 2-5 fps.; You will need to logout/stop and streams that are running through the VLC plugin.

Once that is done you can proceed to add the camera into ZoneMinder with the following settings:

In ZoneMinder

General: Name: x; Source Type: Ffmpeg; Function: Modect (up to you though); Enabled: Tick; Maximum FPS: Empty (I had some issues with it lagging when I used values here); Alarm Maximum FPS: Empty
Source: Source Path: rtsp://IPADDRESS:554/live/mpeg4 (this one seems to be the most reliable); Other Paths: rtsp://IPADDRESS:554/live/h264 , rtsp://IPADDRESS:554/live/mjpeg; Remote Image Colours: 24 bit colour; Capture Width: 720; Capture Height: 480
Buffers: Warm up Frames: 10; Pre Event Image Count: 10; Post Event Image Count: 10; Stream Replay Image Buffer: 1000; Alarm Frame Count: 2

Notes: This 2 Megapixel camera works.; It has a real IR filter than physically moves into place when IR mode engages.; Has POE (Power-over-Ethernet) support verified with a Zyxel GS1100

Adding the camera into ZoneMinder with the following settings:

In ZoneMinder

General: Name: x; Source Type: Ffmpeg; Function: Modect (up to you though); Enabled: Tick; Maximum FPS: At your choice, verifed with 8 FPS; Alarm Maximum FPS: At your choice, verified with 12 FPS
Source: Source Path: rtsp://username:password@IPADDRESS:554/live/mjpeg; Remote Image Colours: 24 bit colour; Capture Width: 720; Capture Height: 480
Buffers: Warm up Frames: 10; Pre Event Image Count: 10; Post Event Image Count: 10; Stream Replay Image Buffer: 2000; Alarm Frame Count: 2

Notes: This 2 Megapixel IP camera works.; It has a real IR filter than physically moves into place when IR mode engages.; Has POE (Power-over-Ethernet) support verified with a POE switch TP-Link TL-SF1008P, and a POE injector TL-POE150S; Tested with ZoneMinder v.1.28.1; Works fine with all supported resolutions (1920x1080; 1280x720; 720x480)

Adding the camera into ZoneMinder with the following settings:

In ZoneMinder

General: Name: x; Source Type: Ffmpeg; Function: Modect (or any of your choice); Enabled: Tick; Maximum FPS: 50 (I limited FPS in the camera interface itself to 10); Alarm Maximum FPS: At your choice, I left it blank
Source: Source Path: rtsp://username:password@IPADDRESS:554/live/h264; Remote Method: RTP/RTSP; Remote Image Colours: 24 bit colour; Capture Width: 1280 (should be equal to whatever you choose in your camera settings); Capture Height: 720 (should be equal to whatever you choose in your camera settings)
Buffers: Image Buffer Size (frames): 50; Warm up Frames: 25; Pre Event Image Count: 25; Post Event Image Count: 25; Stream Replay Image Buffer: 1000; Alarm Frame Count: 1