Brickcom

From ZoneMinder Wiki
Jump to: navigation, search

Brickcom was very forthcoming with the path to the video sources, they made finding the video a lot faster.

WCB-100a

This camera is 802.11 b/g/n (at least b/g)
It is also wired and the documents indicate is is PPoE
Cameras came with Channel 1 set to H.264, Channel 2 set to MJPEG
out of the box. Check them prior to using them though You can access
most of the settings from firefox, but if you want to see the video
in the setup tool you have to use Windows as video display in the
tool demands ActiveX. I just open a path to the raw video and watch
it that way while I do changes in another browser window.
Both mjpeg and mpeg4 work as indicated.
format mjpeg for the cameras using channel 2 as the source is:
http://camera_ip/channel2
Some of them may need the login and password:
http://login:pwd@camera_ip/channel2
Format mpeg4 is as follows, this will be on channel 1
rtsp://camera_ip/channel1
I have not needed to use the login to access this stream.

ZM Source info for mjpeg stream
Tab

+ General
    Name                                test1
    Source Type                         remote
    Function                            Whatever you have set
    Enabled                             []     check it to start capture
    Linked Monitors                     Whatever
    Maximum FPS                         5 (my setting)
    Alarm Maximum FPS                   10 (ditto)
    Reference Image Blend %ge           7 
    Triggers                            none
+ Source
    Remote Protocol                     http	
    Remote Method                       simple
    Remote Host Name                    ip_address OR login:pwd@ip_address
    Remote Host Port                    80   (unless you have set something different)
    Remote Host Path                    channel2 (unless you are using channel1)
    Remote Image Colors                 24 bit
    Capture Width (pixels)              1280
    Capture Height (pixels)             800
    Preserve Aspect Ratio               []
    Orientation                         normal 

ZM Source info for mpeg4 stream
Tab

+ General
    Name                                test1
    Source Type                         remote
    Function                            Whatever you have set
    Enabled                             []     check it to start capture
    Linked Monitors                     Whatever
    Maximum FPS                         5 (my setting)
    Alarm Maximum FPs                   10 (ditto)
    Reference Image Blend %ge           7 
    Triggers                            none
+ Source
    Remote Protocol                     rtsp	
    Remote Method                       rtp/rtsp
    Remote Host Name                    ip_address OR login:pwd@ip_address
    Remote Host Port                    554  (unless you have set something different)
    Remote Host Path                    channel1 (unless you are using channel2)
    Remote Image Colors                 24 bit
    Capture Width (pixels)              1280
    Capture Height (pixels)             800
    Preserve Aspect Ratio               []
    Orientation                         normal 

Camera also does H.264, and VLC will display it just fine, but I had no luck with ZM.


WCB-100Ap-0c

This camera is 802.11 a/b/g/n (at least a/b/g)
It is also wired and the documents indicate is is PPoE
I have been using it on the a side
Cameras came with Channel 1 set to H.264, Channel 2 set to MJPEG
out of the box. Check them prior to using them though You can access
most of the settings from firefox, but if you want to see the video
in the setup tool you have to use Windows as video display in the
tool demands ActiveX. I just open a path to the raw video and watch
it that way while I do changes in another browser window.
Both mjpeg and mpeg4 work as indicated.
format mjpeg for the cameras using channel 2 as the source is:
http://camera_ip/channel2
All I tested needed the login and password:
http://login:pwd@camera_ip/channel2
Format mpeg4 is as follows, this will be on channel 1
rtsp://camera_ip/channel1
I have not needed to use the login to access this stream.


ZM Source info for mjpeg stream
Tab

+ General
    Name                                test1
    Source Type                         remote
    Function                            Whatever you have set
    Enabled                             []     check it to start capture
    Linked Monitors                     Whatever
    Maximum FPS                         5 (my setting)
    Alarm Maximum FPS                   10 (ditto)
    Reference Image Blend %ge           7 
    Triggers                            none
+ Source
    Remote Protocol                     http	
    Remote Method                       simple
    Remote Host Name                    ip_address OR login:pwd@ip_address
    Remote Host Port                    80   (unless you have set something different)
    Remote Host Path                    channel2 (unless you are using channel1)
    Remote Image Colors                 24 bit
    Capture Width (pixels)              1280
    Capture Height (pixels)             800
    Preserve Aspect Ratio               []
    Orientation                         normal 

ZM Source info for mpeg4 stream
Tab

+ General
    Name                                test1
    Source Type                         remote
    Function                            Whatever you have set
    Enabled                             []     check it to start capture
    Linked Monitors                     Whatever
    Maximum FPS                         5 (my setting)
    Alarm Maximum FPs                   10 (ditto)
    Reference Image Blend %ge           7 
    Triggers                            none
+ Source
    Remote Protocol                     rtsp	
    Remote Method                       rtp/rtsp
    Remote Host Name                    ip_address OR login:pwd@ip_address
    Remote Host Port                    554  (unless you have set something different)
    Remote Host Path                    channel1 (unless you are using channel2)
    Remote Image Colors                 24 bit
    Capture Width (pixels)              1280
    Capture Height (pixels)             800
    Preserve Aspect Ratio               []
    Orientation                         normal

Camera also does H.264, and VLC will display it just fine, but I had no luck with ZM.

Retrieved from "?title=Brickcom&oldid=4533"