Difference between revisions of "IEI Technology Corp. IVC-268G-R20"
(Created page with "IVC-268G-R20 Data sheet can be found here: http://www.nextwarehouse.com/item/?876363_IEI_TECHNOLOGY_IVC268GR20 The IVC-268G-R20 is similar to the KesCom PG104, uses a Techwell...") |
|||
| (12 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
IVC-268G-R20 | '''IVC-268G-R20''' | ||
Data sheet can be found here: http://www.nextwarehouse.com/item/?876363_IEI_TECHNOLOGY_IVC268GR20 | |||
The IVC-268G-R20 is similar to the KesCom PG104, | Data sheet for this card can be found here: http://www.nextwarehouse.com/item/?876363_IEI_TECHNOLOGY_IVC268GR20<br/>The IVC-268G-R20 uses a Techwell TW6802 chip, installation is similar to the KesCom PG104,<br/>To use this capture card you need to compile the driver. For Ubuntu Server 12.04.04 LTS with 3.13 kernel the source can be found at https://gitorious.org/tw68/.<br/>~$ sudo apt-get install git<br/>~$ sudo apt-get install build-essential<br/>~$ mkdir techwell<br/>~$ cd techwell<br/>SEE NOTE BELOW<br/>~$ git clone git://gitorious.org/tw68/smokeyjoness-tw68-v2.git<br/>~$ cd smokeyjoness-tw68-v2<br/>~$ make<br/>~$ sudo make install<br/>~$ sudo modprobe tw68<br/>(Note smokeyjoness-tw68-v2 was successfully installed on 64bit Server, for 32bit server (same hardware) smokeyjoness-tw68-v2 did not work so I use git clone git://gitorious.org/tw68/pocek-tw68-v2.git)<br/>After compiling and "loading" the tw68 modules, you need to check that the modules are actually loaded (lsmod | grep tw). You should have the similar output:<br/> | ||
To use this capture card you need to compile the driver. For Ubuntu Server 12.04.04 LTS with 3. | |||
~$ lsmod | grep tw<br/> | |||
<pre> | |||
tw68 44633 2 | |||
~$ lsmod |grep tw | |||
tw68 44633 2 | |||
videodev 86588 3 tw68 | videodev 86588 3 tw68 | ||
videobuf_dma_sg 18786 1 tw68 | videobuf_dma_sg 18786 1 tw68 | ||
videobuf_core 25409 2 tw68,videobuf_dma_sg | videobuf_core 25409 2 tw68,videobuf_dma_sg | ||
btcx_risc 13400 1 tw68 | btcx_risc 13400 1 tw68 | ||
</pre> | |||
~$ cd /dev<br/>You should see now video0, video1, video2, video3. | |||
This video card has dip SW to program card address (how it actually work could be checked later if someone has more then one card installed on linux box) | |||
Latest revision as of 14:55, 4 August 2014
IVC-268G-R20
Data sheet for this card can be found here: http://www.nextwarehouse.com/item/?876363_IEI_TECHNOLOGY_IVC268GR20
The IVC-268G-R20 uses a Techwell TW6802 chip, installation is similar to the KesCom PG104,
To use this capture card you need to compile the driver. For Ubuntu Server 12.04.04 LTS with 3.13 kernel the source can be found at https://gitorious.org/tw68/.
~$ sudo apt-get install git
~$ sudo apt-get install build-essential
~$ mkdir techwell
~$ cd techwell
SEE NOTE BELOW
~$ git clone git://gitorious.org/tw68/smokeyjoness-tw68-v2.git
~$ cd smokeyjoness-tw68-v2
~$ make
~$ sudo make install
~$ sudo modprobe tw68
(Note smokeyjoness-tw68-v2 was successfully installed on 64bit Server, for 32bit server (same hardware) smokeyjoness-tw68-v2 did not work so I use git clone git://gitorious.org/tw68/pocek-tw68-v2.git)
After compiling and "loading" the tw68 modules, you need to check that the modules are actually loaded (lsmod | grep tw). You should have the similar output:
~$ lsmod | grep tw
tw68 44633 2 videodev 86588 3 tw68 videobuf_dma_sg 18786 1 tw68 videobuf_core 25409 2 tw68,videobuf_dma_sg btcx_risc 13400 1 tw68
~$ cd /dev
You should see now video0, video1, video2, video3.
This video card has dip SW to program card address (how it actually work could be checked later if someone has more then one card installed on linux box)
